Ragnar Robotics home

Ragnar M, up close

Ragnar M does the repetitive work in machine shops and print farms: it loads CNC machines, swaps print plates and moves parts between stations. It uses the same base as Ragnar C, with an arm on a fixed riser on top instead of the mast.

57.4 in41 in
CAD view of Ragnar M, the CNC machine tending robot, from the front right: the base, the two cassettes, the riser and the arm with its gripper.
CAD view of Ragnar M from the rear left: the push handle with the operator panel, the cassettes and the riser.
Rendering of Ragnar M, a mobile robot for CNC machine tending, in a grey studio with its orange status lights on: the base, the cassettes, the riser and the arm with its gripper.

How it works

Set up
We prepare one machine: the door, the work holding and the cycle signal. We make the cassettes for your part.
Park
Ragnar M parks at the machine and finds the vise with its wrist camera.
Work
It unloads the finished part and loads the next one, cycle after cycle. Once one machine runs well, the same robot can cover the next.
Report
You get photos and a log of everything it did.

Built for

CNC mills and lathes

Haas
VF series, Mini Mill, UMC and ST lathes
DN Solutions
DNM mills, Lynx and Puma lathes
Mazak
VCN mills and Quick Turn lathes
Okuma
Genos M mills and Genos L lathes
Hurco
VM and VMX mills
Brother
Speedio
FANUC
Robodrill
DMG Mori
CMX mills and NLX lathes
Tormach
1100M and 770M

3D printers

HP
Multi Jet Fusion 5600 and 1200 parts, from unpacking to finishing
Formlabs
Form 4 and Form Wash
Stratasys
F170, F270 and F370
Markforged
Mark Two and X7
UltiMaker
Factor 4, S7 and S8
Print farms
Bambu Lab and Prusa

What it needs

Door
An automatic door, or one we fit
Work holding
An air vise or an air chuck
Signal
The machine tells the robot when a cycle ends
Reach
We check it on your machine before a pilot
Cycle time
Cycles of ten minutes or more suit it best, so one robot can cover more than one machine

Inside

The same base as Ragnar C, with a collaborative arm on a fixed riser on top. The base carries the battery, the computer, a lidar and a depth camera, and the deck carries a cassette for raw stock and one for finished parts.

Arm reach Fairino FR5, from the shoulder
36.3 in
Arm payload Rated, gripper included
11 lb
Arm height Base of the arm, on the riser
33.5 in
Height Arm folded
42 in
12345678
  1. Arm. A Fairino FR5: 11 lb (5 kg) payload and 36.3 in (922 mm) reach, to load a machine through its door.
  2. Riser. A fixed steel riser holds the arm 33.5 in (850 mm) off the floor, so it reaches into a machine and down to its cassettes.
  3. Gripper. An electric parallel gripper. A RealSense D405 on the wrist checks every grip up close.
  4. Lidar and camera. A 2D lidar behind the glass band at the front stops it for obstacles. A RealSense D435 at the front corner lines it up at each machine.
  5. Computer. An NVIDIA Jetson Orin Nano Super, the safety controller and the electronics, inside the base.
  6. Battery. One battery pack, swapped through the rear door.
  7. Drive. Two hub motor wheels and four casters.
  8. Cassettes. One for raw stock and one for finished parts, on the deck.

The details

The parts that do the work, up close.

Close up CAD rendering of the electric gripper on the wrist of the arm, with the RealSense D405 on its side.
Gripper. An electric parallel gripper takes the finished part out of the machine and puts the next one in. A RealSense D405 on the wrist checks every grip.
Close up CAD rendering of a corner of the Ragnar M base: the black glass band, the light line, an emergency stop and a lifting eye.
Base. A lidar behind the glass band at the front, a depth camera at the front corner, an emergency stop on each corner of the deck, lifting eyes and a light line all around.
Close up CAD rendering of the Ragnar M deck with the raw stock columns behind the riser and the divided tray for finished parts at the rear.
Cassettes. Raw stock stands in guided columns behind the riser, and finished parts go into the divided tray at the rear.
Close up CAD rendering of the arm base on top of the fixed riser, with the orange status light on the ring.
Riser. A fixed steel riser holds the FR5 33.5 in (850 mm) off the floor. The ring under the arm is its status light.

Dimensions

The side, front, rear and top views are at the same scale, with the arm folded.

41 in (1.04 m)42 in (1.07 m)
28 in (0.72 m)
28 in (0.72 m)
Three quarter view of the Ragnar M CAD model.

Target specifications

Size

Footprint
28 by 41 in (0.72 by 1.04 m) with the bumper; fits a 36 in door
Height
42 in (1.07 m) with the arm folded

Motion

Drive
Two hub motor wheels and four casters
Arm
Fairino FR5 on a fixed riser, 11 lb (5 kg) payload, 36.3 in (922 mm) reach

Tools and parts

Gripper
Electric parallel gripper
Parts
One cassette for raw stock and one for finished parts on the deck, made for your part
Part weight
Up to about 6.5 lb (3 kg); the gripper uses the rest of the 11 lb payload

Power and sensing

Power
One battery pack, swapped through the rear door
Computer
NVIDIA Jetson Orin Nano Super
Sensing
A 2D lidar behind the front glass band, a RealSense D435 depth camera at the front corner and a RealSense D405 on the wrist
Operator
Panel at the rear with a 10.1 in touch screen, start, pause and reset buttons and a key switch
Safety
An emergency stop at each corner, cliff sensors on the bumpers and a safety bumper all around; the lidar stops it for obstacles

Talk to us

Send us a task from your shop and we will show you how Ragnar M would do it.

Send us your taskBook a 15 minute call

See the whole family, drawn to scale, on the home page.